I. Introduction: bold innovation and design through a wall device, the kind of equipment is the basis for most of the country is currently assembled wall formwork equipment on board. Respectively, by foaming agitation and pumping system formwork system composed of two perfusion, due to having less investment, high efficiency, producing many kinds of wall and in the future will dominate the market. Stir foam material pumping systems: stand modules: two, the superiority of the device: In accordance with the pumping capacity I will be divided into large, medium and small, a pumping system using foaming agitation. Pumped per hour were 6 cubic meters, 10 cubic meters, 20 cubic meters, regardless of the choice of the kind of full production, it is necessary to only three workers, including two workers to complete tasks foaming agitation, a worker hand pump infusion tube to mold can be, this way you can save a lot of production and employment numbers, improve production efficiency. Stripping the way it uses two-time overall stripping formwork perfusion system is mainly a one-time for each group can produce 40 panels, stripping fast, high efficiency is conceivable Third, the production line uses: it can be widely used production Series lightweight wall panels, the kind of production line is a versatile product line. Including pure lightweight foam wall panels, lightweight foam sandwich wall panels, inorganic non-combustible exterior insulation board, fire door core and so on. Lightweight, light wallboard quality solid economy, 75mm to 120mm thick wall board plaster masonry walls on both sides of the weight + 1/3 ~ 1/5. Solid wall beams to optimize structure, easy to install in a non-load-bearing beams outside, so that the whole interior layout more reasonable. Thin body - increased use of the area by the National Building partition board norms, with a solid wall 75mm and 100mm respectively, instead of the traditional brick 120mm and 180mm thick brick wall. Use a solid wall system, construction of the wall to increase 10 ~ 12m to extend the use of 1m2 area, usage increased by 4% to 6%, is well suited for retail and residential walls and household. Fireproof noncombustible solid wall partition system performance up to the national A-level standards, after siding installation is complete, with excellent stability and integrity, good fire resistance, fire and smoke can poison gas confined within the area affected by the fire, and do not emit toxic gases, for your safety more of a guarantee. Insulation, solid wall insulation is building an outdoor, ideal for energy saving in the wall plate. It has on climate change with the seasons and automatically adjust the indoor air moisture content function, set the humidity level to maintain a balance, to the effect of ecological regulation, in line with the development trend of modern residential architecture. 100mm thick insulation capacity of the heart wall of noise 46dB, much higher than other brick wall of sound insulation, sound insulation in line with the requirements of the National Housing. Moisture-proof, water-proof solid wall panels for medium density fiber reinforced cement slab, has a good waterproof, moisture resistant, can be used for kitchen, bathroom, basement and other wet areas, wall plates will not appear due to moisture absorption of pine, back to halogen deformation, strength decreases and so on. Experiments show that, in the absence of wallboard can make any finishes, filled with water after the cell body with cement bonding, the back wall can be kept dry without leaving any traces, the walls will not appear condensation in humid weather drops. Simple construction, short construction period is assembled solid wall construction, the wall height of 4m or less, each about three workers, an average of one day to ship 15m2 more skilled workers, and no longer smooth sided wall plastering and masonry building wall construction efficiency compared to more than 10 times. Environmental GRC light wallboard product features a capacity of light: per square meter wall 46 ± 2kg, brick and concrete walls weight ratio decreased about 80%, reducing the project cost basis; 2, thin wall: 90mm thick and 24cm Performance brick rather, can expand the use of housing area of ??10% -13%; 3, excellent quality: compressive strength, impact resistance, flexural failure load, surface density, hanging power, sound insulation, fire resistance, drying shrinkage, etc. are in line with national building materials industry, "JG / T169- 2005 building walls with the Light Board" standard; 4, board level: reducing mortar layer, directly after the putty stucco; 5, fast installation: nails, saws, drilling, planing cutting easy, flexible construction, pipe and take the easy line, saving time and labor to install and improve construction speed 3-5 times; 6, low prices: prices are lower than traditional solid walls, reducing the total cost of the project; 7, no cracking: original slot tenon structure and construction technology, a good solution to the problems of the industry for many years the wall cracking problems.